<div dir="ltr">The wind loading data is generally available as part of the specifications by the dish manufacturer. Dishes of 1.8M and 2.4M are common. Dishes without such specifications are likely to not have been completely categorized as to RF performance either. Full characterization is required to have high confidence in the G/T numbers. <div><br></div><div>The wind load depends on the design requirements. In Florida here, we have to engineer fixed microwave dishes to the state requirements based on the zone which ranges from 100mph to 150mph.  It's not trivial at the high end even for a garage door. Since square laws are involved, forget about meeting them. It's probably best to engineer to a reasonable operating limit and to a stowed configuration during storms as only the latter can meet code in South Florida.  (During Andrew all the dishes blew off the National Hurricane Center). </div><div><br></div><div>BTW, a PE is required to do a site specific calculations for any commercial installation. So avoid fixed installations. </div><div><br></div><div>We should probably have characterizations for stowed, deployed but not-operating, and operating. </div><div><br></div><div>Just my $0.02</div><div><br></div><div><br></div><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Dec 7, 2019 at 11:57 AM Michelle Thompson via Ground-Station <ground-station@lists.openresearch.institute> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="font-size:1rem;word-spacing:1px;border-color:rgb(49,49,49);color:rgb(49,49,49)" dir="auto">I hired a local open source robotics designer to go over our JAMSAT collaboration. This is a heavy-<span style="font-size:1rem">duty automated AZ-EL tracking station capable of LEO to Gateway. We fully intend for integration with SatNOGs. The demonstration is expected to be at Tokyo Ham Fair 2020. </span></div><div style="font-size:1rem;word-spacing:1px;border-color:rgb(49,49,49);color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;word-spacing:1px;background-color:rgba(0,0,0,0);border-color:rgb(212,212,213);color:rgb(212,212,213)" dir="auto"><font style="color:rgb(49,49,49)">Our engineering consultant’s name is James Newton. You may recognize him as 2018 Hackaday Superconference prize winner. He’s very active in the San Diego Maker Movement. I’ve volunteered with him at events for 7 years. </font></div><div style="font-size:1rem;word-spacing:1px;background-color:rgba(0,0,0,0);border-color:rgb(212,212,213);color:rgb(212,212,213)" dir="auto"><font style="color:rgb(49,49,49)"><br></font></div><div style="font-size:1rem;word-spacing:1px;background-color:rgba(0,0,0,0);border-color:rgb(212,212,213);color:rgb(212,212,213)" dir="auto"><font style="color:rgb(49,49,49)">All of his engineering solutions for motor control are open source and are ready to go. He anticipates no further charges for his time, and is ready to help integrate his work for our prototype. I paid him out of pocket. No ORI money was used. </font></div><div style="font-size:1rem;word-spacing:1px;background-color:rgba(0,0,0,0);border-color:rgb(212,212,213);color:rgb(212,212,213)" dir="auto"><font style="color:rgb(49,49,49)"><br></font></div><div style="font-size:1rem;word-spacing:1px;background-color:rgba(0,0,0,0);border-color:rgb(212,212,213);color:rgb(212,212,213)" dir="auto"><font style="color:rgb(49,49,49)">What do we need to do to get to the prototype for demonstration?</font></div><div style="font-size:1rem;word-spacing:1px;border-color:rgb(49,49,49);color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;word-spacing:1px;border-color:rgb(49,49,49);color:rgb(49,49,49)" dir="auto">The sequence proposed moving forward:</div><div style="font-size:18px;word-spacing:1px;border-color:rgb(49,49,49);color:rgb(49,49,49)" dir="auto"><div style="font-size:1rem;border-color:rgb(49,49,49)">- Collect as many as possible dish data sheets with weight and mounting pattern to try to find commonalities.</div><div style="font-size:1rem;border-color:rgb(49,49,49)">- Purchase / "procure" a "2 meter" (6 foot) diameter dish for local development. If Doug Phelps can send me all the remaining 2m dishes, then I will take them for prototype stations. </div><div style="font-size:1rem;border-color:rgb(49,49,49)">- Pay for mechanical design of mount for common dish support maximum scope of commonly available dishes<br>- Fabrication / adjustment of mount locally. Hopefully it can be welded using alignment "tricks" to keep the bearings right.<br>- Attachment of actuators to axis (steppers / DC motors). Possible further mechanical design.<br>- Attachment of encoder system  (James to lead)<br>- Drive / servo controller / motion control electronics (James to lead)<br>- Interfacing with existing control system (This is us)</div><div style="border-color:rgb(49,49,49)"><br></div><div style="font-size:1rem;border-color:rgb(49,49,49)">the first step is to gather data on the mechanical aspects of the target antennas; weight and mounting bolt pattern. The consensus from the local microwave and EME people is a pipe will be best.</div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto">The mechanical designer doing the CAD (recommended by James) needs to know how fast they needed to move and how much load they would take from the wind. That last one is probably tricky to find out, but maybe we can prototype a solid mount and attach some strain gages to a data logger if we can’t find out from existing sources. </div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto">Got answers, questions, feedback? Let’s hear it! </div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto">-Michelle W5NYV </div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto"><br></div><div style="font-size:1rem;border-color:rgb(49,49,49)" dir="auto"><br></div></div>-- <br><div dir="ltr"><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><div dir="ltr">-Michelle W5NYV<br><br><div dir="ltr">"Potestatem obscuri lateris nescis."<br></div><div><br></div></div></div></div></div></div></div></div>
</blockquote></div>