<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
<p>The standard IF for DVB-S2 receivers is 950 to 2150 MHz.</p>
<p>DB6NT was selling a down-converter from 10489-10500 MHz to
1129-1140 MHz for P4A.</p>
<p><a class="moz-txt-link-freetext" href="https://shop.kuhne-electronic.com/kuhne/en/shop/new/MKU+LNC+10+OSCAR+P4A/?card=1832">https://shop.kuhne-electronic.com/kuhne/en/shop/new/MKU+LNC+10+OSCAR+P4A/?card=1832</a></p>
<p>I'm not sure what decimation has to do with receiving DVB-S2. The
entire 10 MHz signal needs to be demodulated. Individual baseband
frames will be selected for processing, but I call that
de-multiplexing.<br>
</p>
<p>Ron W6RZ<br>
</p>
<div class="moz-cite-prefix">On 1/25/19 15:32, David Vieira via
Ground-Station wrote:<br>
</div>
<blockquote type="cite"
cite="mid:1513072063.1340144.1548459146399@mail.yahoo.com">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<div class="ydp1f38d99eyahoo-style-wrap"
style="font-family:Helvetica Neue, Helvetica, Arial,
sans-serif;font-size:13px;">
<div>Michelle - Thanks for posting. I'll frame some of the
questions.<br>
</div>
<div><br>
</div>
<div>Typical 10 GHz terrestrial contesting rigs are Heterodyne;
that is a Mixer works with a Local Oscillator (LO) to take the
RF down to an IF (Intermediate Frequency).</div>
<div>For an SDR, that IF can be digitized by an Analog-Digital
Converter.</div>
<div><br>
</div>
<div>The most popular IF for contesting/SSB rigs is 144 MHz. </div>
<div>For a data BW of 10 MHz that may or may not be a fast
enough IF carrier. If we can digitize and recover the data,
it would allow a lot of re-use of existing equipment.</div>
<div><br>
</div>
<div>I've heard suggestions/proposals up to the 1.2 GHz Ham
band.</div>
<div>In some sense, the IF carrier could be 144/220/440/915/1200
MHz, or even any Non-Ham frequency in between.</div>
<div><br>
</div>
<div>There are a lot of proof of existence designs for a 10 GHz
Mixed down to an IF; and lots of off the shelf ADC
dev-boards. (catch me off thread for details).</div>
<div><br>
</div>
<div>Some questions I have are: </div>
<div>---from an FPGA side of the SDR, what data rate(s) can the
FPGA absorb in to a decimator? </div>
<div><br>
</div>
<div>Must we decide upfront on a single frequency; or </div>
<div>preferably allow flexibility in the RF front end design
(ie, Mixer, PLL and Local Oscl hardware choices) by allowing a
wide and programmable variety of ADC and decimation rates?</div>
<div><br>
</div>
<div>{This is where RF and Digital folks must communicate across
walls.} ;-)</div>
<div><br>
</div>
<div>Comments welcome.</div>
<div><br>
</div>
<div>regards,</div>
<div>David</div>
<div>KI6CLA</div>
<div><br>
</div>
<div><br>
</div>
</div>
<div id="ydp40e62e6byahoo_quoted_8708381549"
class="ydp40e62e6byahoo_quoted">
<div style="font-family:'Helvetica Neue', Helvetica, Arial,
sans-serif;font-size:13px;color:#26282a;">
<div> On Friday, January 25, 2019, 2:41:54 PM PST, Michelle
Thompson via Ground-Station
<a class="moz-txt-link-rfc2396E" href="mailto:ground-station@lists.openresearch.institute"><ground-station@lists.openresearch.institute></a> wrote: </div>
<div><br>
</div>
<div><br>
</div>
<div>
<div id="ydp40e62e6byiv6388574106">
<div dir="ltr">
<div dir="ltr">While we are striving to enable all sorts
of wonderful designs by putting prototypes into GNU
Radio, a central goal is to design our own hardware.<br>
<br>
We've had a lot of progress on the protocol and
algorithm front (GSE, LDPC, some of the polyphase). <br>
<br>
Some fundamental decisions about our own hardware need
to be made.<br>
<br>
When we receive, we expect to have to decimate. This
is because we are receiving at a relatively high
frequency (10GHz).<br>
<br>
Our bandwidth is (up to) 10MHz. For DVB-S2/X, we fix
our sampling rate, depending on what bandwidth we want
to support. We have a lot of freedom here.<br>
<br>
Picking the right frequencies for the receive chain is
therefore important.<br>
<br>
What are our options? <br>
<br>
What options make the best sense?<br>
<br>
I'd like to build and test as soon as possible, so
let's get some discussion going.<br>
<br>
<div>
<div dir="ltr"
class="ydp40e62e6byiv6388574106gmail_signature">
<div dir="ltr">
<div>
<div dir="ltr">
<div>
<div dir="ltr">
<div dir="ltr">-Michelle W5NYV<br>
<br>
<div dir="ltr"><br>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
_______________________________________________<br>
Ground-Station mailing list<br>
<a href="mailto:Ground-Station@lists.openresearch.institute"
rel="nofollow" target="_blank" moz-do-not-send="true">Ground-Station@lists.openresearch.institute</a><br>
<a
href="http://lists.openresearch.institute/mailman/listinfo/ground-station"
rel="nofollow" target="_blank" moz-do-not-send="true">http://lists.openresearch.institute/mailman/listinfo/ground-station</a><br>
</div>
</div>
</div>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
Ground-Station mailing list
<a class="moz-txt-link-abbreviated" href="mailto:Ground-Station@lists.openresearch.institute">Ground-Station@lists.openresearch.institute</a>
<a class="moz-txt-link-freetext" href="http://lists.openresearch.institute/mailman/listinfo/ground-station">http://lists.openresearch.institute/mailman/listinfo/ground-station</a>
</pre>
</blockquote>
</body>
</html>